---

WASTE KING® EXCLUSIVES

• Anti-Jam Swivel Impellers rotate out of the way of an impending jam, then fall back into grinding position, pulverizing waste particles.
• Stainless Steel Undercutter Blade located beneath the grind ring snips fibrous and stringy waste into small particles making them less likely to clog drain lines.
• Hush-Cushions® isolate the unit from metal to metal contact, significantly reducing noise level. Hush-Cushions® are specially compounded and designed to withstand vibration and tension, and have a built-in safety splash guard.

---

FEATURES

• 1 1/2 HP disposer, dual voltage
• Fan cooled motor with ball bearing construction and integral overload protection
• Dynamically balanced for smooth, long wearing operation
• Hush Cushion® mounting connection for 6" cone or sink opening includes an auxiliary water inlet
• Stainless steel grind chamber
• Corrosion proof, glass reinforced polyester exit chamber
• 6 1/4" Diameter heavy duty, cast stainless steel turntable
• 2 Jam resistant, hardened stainless steel swivel impellers with tungsten carbide inserts
• Stainless steel undercutter blade
• Hard, tough, cast alloy grind ring with dual stage grinding action
• Lifetime particle size control by non-wearing exit slots

MOUNTING SYSTEMS
Sink Mount Assembly (SM) #2539 3 1/2" Bolt-in adapter for suspended models with 6" throat	Trough Mount Assembly (TM) #2536 6" Weld-in flange for models with 6" throat	Basic Cone Assembly (B) 12", 15", or 18" Cone with Swirl Sprays	All-Purpose Cone Assembly (AP) 12", 15", or 18" Cone with Swirl Sprays Silver Guard Scrap Ring	Dish Table Cone Assembly (DT) 12", 15", or 18" Cone with Swirl Sprays 12", 15", or 18" Cone Cover Scrap Ring

PLUMBING Models 1500-1 and 1500-3 are equipped with a drain outlet for connection to a conventional 1 1/2" trap. The trap may be connected to a 2" branch waste line running directly into a waste stack. We recommend a slope in the waste line of not less than 1/4" per foot. Connect directly to waste line, not through a grease interceptor. MOTOR DATA 1500-1 60 cycle 1 Phase 1 1/2 HP 1725 RPM 110-120/220-240 volts 14.4/7.2 amps 1500-3 60 cycle 3 Phase 1 1/2 HP 1725 RPM 208-240/460 volts 4.4/2.2 amps Bearing permanently lubricated. Manual reset overload protection in motor.	NOTE: Disposer assembly includes disposer, mountings, and drain outlet. Other items shown in gray are available in mounting systems or ordered separately. Installation should be made in accordance with local codes. All specifications subject to change without notice. Assembly should be installed in accordance with Waste King's printed installation instructions. * Items available through Waste King
TO SPECIFIERS So that you may be assured of receiving the fine quality you expect when you specify a WASTE KING® FOOD WASTE REMOVAL SYSTEM, we include the following sample specification for your convenience: Food waste disposer shall be 1 1/2 HP, 60 cycle, 1 Phase with 110-120/220-240 volts, or 3 Phase with 208-240/460 volts. There shall be a rubber Hush Cushion® between the disposer and the cone or sink to eliminate metal to metal contact. Turntable shall be of stainless steel with jam-resistant swivel impellers of hardened stainless steel with Tungsten carbide inserts. Turntable shall have stainless steel cutting blades rotating below the exit slots Grind ring shall be precision ground on all cutting surfaces and shall have non-wearing, size controlled exit slots. Disposer shall have a totally enclosed, continuous duty, fan cooled motor with integral overload protection. Unit shall be Waste King® model 1500-1 or 1500-3.

ROUGH-IN DIMENSIONS With drain line connections

Cone Mounted Models

Sink Mounted Models with #2539 Sink Mount Installation Special Order ONLY